Modified Cub Cadet Makes Right Size Loader/Backhoe

Modified Cub Cadet Makes Right Size Loader/Backhoe TRACTORS Loaders en Esposito’s Cub Cadet loader/backhoe does everything his big Case 580 does just in smaller bites The Cub 1772 Super with its 3-cylinder diesel can get some good-sized jobs done “It amazes me every time I use it ” says Esposito “I can pick up 1 000 lbs with the 12-cu ft bucket and use forks to handle pallets When I want to use the backhoe I just flip the seat around and go to work ” Like all post IH Cubs it has an aluminum transaxle housing It is known for a problem where bolts that loosen due to vibration create play between the transmission and the frame causing the trans mounts to break off Esposito found an older cast iron housing and swapped out his aluminum one “The cases were only a few thousanths of an inch different so it just took shimming to replace the gears differential and axle in the cast iron case ” recalls Esposito He got a Kwik Way loader from a neighbor who had it on a Cub 782 Esposito modified the mounting brackets and fabricated a new 5 1/2 cu ft bucket for it He used 1/8-in steel with 1/4-in where he needed reinforcement He also made quick-tach brackets for the bucket and a forklift attachment which he also fabricated “The forklift frame is 1/8-in 1 3/4-in steel tubing with 1/4-in steel for the quick-tach brackets ” says Esposito “I used cutting edges from dozer blades for the forks The hardened steel will flex but it won’t bend and always returns to the original position ” The backhoe which he ordered from a distributor in Oregon was designed for Cat I 3-pt hitches It came with its own operator’s seat hydraulic pump and reservoir Esposito cut away the operator’s seat pump and reservoir and modified the Cub’s seat to raise and swivel to the rear He devised a quick-tach system with a receiver plate on back of the Cub The receiver plate consists of 3/4-in steel upper arms that are bolted to the Cub frame and a lower yoke that consists of 2 J-hooks The yoke is welded to a frame that extends forward to the subframe of the loader The 2 frames are bolted in place to make a single unit “I replaced the 3-pt on the backhoe with a frame for a pipe that slips into the yoke and clevis-type receivers that pin to the arms ” says Esposito “I back up to the backhoe connect the hydraulics and it lifts itself into place for pinning “ Esposito modified the Cub seat to lift and rotate He pinned four 6-in lengths of 3/4-in sq steel tubing between angle iron brackets bolted to the Cub The other ends of the tubing are pinned to the bottom of a swivel plate from an old office chair He attached the Cub seat to the swivel plate Pins on a retraction spring lock the seat in place either forward or back “I designed the seat to match my height ” says Esposito “When I raise it up it brings me close to the backhoe controls with the right space to the footrests ” Esposito also changed out the Deere-type control valves for CAT controls He replaced a faulty relief valve and added a second boom swing cylinder “With the one cylinder I could stop the boom with my hand ” says Esposito “I did a mirror image connection on the other side and now it swings with some force ” When he dismounts the backhoe Esposito slips on a 3-pt hitch he fabricated for the quick attach unit He also designed a ripper using a carbide tipped tooth from an asphalt-milling machine 1/4-in steel plate and schedule 80 pipe to fit the yoke on the 3-pt hitch “I doubt it will wear out in my lifetime ” says Esposito Esposito is so satisfied with his Cub loader/backhoe rig that he is transferring some of the ideas to his Case 580 backhoe He also added some new ones like a Bobcat grapple fork modified for quick-tach plates “It belonged to my grandfather who also was a heavy equipment operator ” says Esposito “I made the quick-tach units for it using 1/2-in steel with some 2-in for reinforcement I made 2-in thick 5-in side forks for it using 1/4-in 3 by 3-in and 2 by 6-in carbon steel tubing The bar that supports the forks is solid 2-in steel ” There’s a video showing how the backhoe connects at www farmshow com Contact: FARM SHOW Followup Ken Esposito Clark N J ken6x6@comcast net

To read the rest of this story, download this issue below or click here to register with your account number.